3D PotterBot Micro 8

Micro 1.jpg
Micro 2.jpg
Parts Box.jpg
Micro 1.jpg
Micro 2.jpg
Parts Box.jpg

3D PotterBot Micro 8

2,850.00

The 3D Potterbot Micro 8 is an entry-level 3D ceramic printer. It has all of the great features of our upper level models but in a smaller package and more affordable price.

Quantity:
Add To Cart

New for 2018 - 3D Potterbot Micro-8

 

3D Potterbot Micro 8 is our latest affordable 3D ceramic printer. The small build volume is more than adequate for the classroom environment and teaching institutions. It still has all of the same advantages that our larger machines, still having direct nozzle extrusion and our unique traveling X and Y bed.

The main difference the Micro 8 has versus the larger machines is the drive motors. The micro uses are standard stepper motors which are quite adequate for the smaller build envelope.
This is an ideal machine for traveling or if you are going to transport it from one location to another on regular basis. Built rugged and ready for classrooms, small production environments, universities, and ceramic institutes.

20181207_103018.jpg
micro 11.jpg

The 3DP Micro 8 design uses high-precision linear rails from IGUS, a X and Y axis drive system with precision timing belt, and stepper motors. Our design utilizes traveling X, Y, and Z axis. The X-axis is allowed to travel freely on top of any flat surface. The Z axis and extruder use a reduction gearbox for faster and smoother prints.

The hard anodized linear rail with advanced plastic car bushings will give extended service life, even in harsh environments. By using timing belts we have decreased printing time by as much as 75% for small items. 

Micro 8 uses our 1000ml direct nozzle extruder. Because the extruder is stationary, the clay comes directly out of the nozzle without any hoses, complicated air compressors, or augers. In addition, we are able to print superior quality prints with less air bubbles, in less time, and at larger scales.

Extruder tubes can be easily loaded from any standard pug mill or our new wall mounted hand loader. You can load 5 tubes in less than 10 minutes, that is 60 pounds of clay! The tubes can also be loaded manually with clay purchased from your local ceramic supplier. Clean up is easy and can be accomplished between loading tubes in less than a couple of minutes.

This touch screen Control Center is packed with features and options that make the stand-alone operation of our 3D Potterbot effortless. A simple SD card is inserted with the G code to run your prints. You have complete control over the printer & extruder by being able to adjust the speeds and flows easily through the touch screen. This touch screen is an integral part of our Arm core processor main controller board. (It's not an aftermarket add on).

This is representation the space necessary for the printer. This is the size of the printer when it's moving to its maximum and all axises. In other words this is a size you need on your table or to operate properly

This is representation the space necessary for the printer. This is the size of the printer when it's moving to its maximum and all axises. In other words this is a size you need on your table or to operate properly

What's included:

1. 3D PotterBot Micro

2. Stepper motors on X, Y, Z, extruder

3. 1000ml extruder, 2 tubes

4. 4 nozzles (standard sizes: 3.5, 4.13, 5, and 6.4mm)

5. Parts Box: Alan key set, grease, Acme driver tool, tie wraps, extra screws

6. Power Supply, USB cable

Specifications

Printing Envelope:
X-10” (254mm)
Y-10” (254mm)
Z-12” (305mm)

Printer size:
W-24” L-26” H-25”
Operation space needed: W-31” L-28” H-46”
Bat diameter (printer bed): 13.5" (343mm)
Height to the top of the extruder fully extended is 46" (1168mm)

Average speed: 1.4” to 2.4”/s (35 to 60 mm/s)
Power Supply: Output - 24V 5-6 amps, Input: 110-220V, 50-60 Hertz (No 220V power plug supplied for customers outside of USA).
Power consumption: 24V ~2 amps, ~50 Watt
Main controller board running Smoothieware with Arm Processor Cortex M3 100 - 120 Mhz

Touchscreen included - full control Standalone function, input either SD card with G-code or USB cable for direct control of printer. Recommended slicing programs Simplify3D, Cura, or Repetier.